|
| For INTEL 775 |
|
|
|
| Put black side of HPJ backplate (four holes) into 775 motherboard and the first screw pierces through the bracket and motherboard. |
|
|
| Place the black washers for Intel series on screws. |
|
|
|
|
|
| Shore up the bottom of screw by hands and lock up the blots. The remainder three screws (775) repeat step 1 to step 3. |
|
|
| Apply the thermal paste evenly on the CPU die. |
|
|
|
|
|
| Remove the sticker at the bottom of heatsink, and put the “I”-shaped bracket in notch of the heatsink . |
|
|
| Put the cooler on the central of CPU and the bracket aims at the holes of blot. |
|
|
|
|
|
| Lock up and fix tightly the nuts by diagonal line. (Notice 1: While locking the nuts, please lock tightly after the four nuts lock by diagonal line. Notice 2: Recommend to install the main body before setting up the fans.). |
|
|
| Put one side of fan clip on the fan holder and another side buckles on the hearsink, and hoop up the other fan clips step by step. (According the demands, users can choose to install the heatsink, or heatsink with one or two fans.). |
|
| |
|
|
|
|
|
| Finally, plug in the power connector and finish the installation. |
|
|
|
| |
| For Intel 1366 |
|
|
|
| Put blot of HPJ backplate pierces though the holes of 1366 motherboard. |
|
|
| Apply the thermal paste evenly on the CPU die. |
|
|
|
|
|
| Remove the sticker at the bottom of heatsink, and put the “I”-shaped bracket in notch of the heatsink. |
|
|
| Put the cooler on the central of CPU and the bracket pierce through the blot of backplate. |
|
|
|
|
|
| Lock up and fix tightly the nuts by diagonal line. (Notice 1: While locking the nuts, please lock tightly after the four nuts lock by diagonal line. Notice 2: Recommend to install the main body before setting up the fans.) . |
|
|
| Put one side of fan clip on the fan holder and another side buckles on the hearsink, and hoop up the other fan clips step by step. (According the demands, users can choose to install the heatsink, or heatsink with one or two fans.) . |
|
|
|
|
|
| Finally, plug in the power connector and finish the installation. |
|
|
|
|
| |
| For AMD K8 AM2 |
|
|
|
| Remove the original backplate and bracket. |
|
|
| Put black side of HPJ backplate (six holes) into K8 or AM2 motherboard and the screws pierce through the bracket and motherboard. |
|
|
|
|
|
| Place the white washers of AMD series on the screws. |
|
|
| Shore up the bottom of screw by hands and lock up the blots. The remainder one (K8) or the other three screws (AM2) repeat step 2 to step 4. |
|
|
|
|
|
| Apply the thermal paste evenly on the CPU die. |
|
|
| Remove the sticker at the bottom of heatsink, and put the “I”-shaped bracket in notch of the heatsink . |
|
|
|
|
|
| Put the cooler on the central of CPU and the bracket aims at the holes of blot. |
|
|
| Lock up and fix tightly the nuts by diagonal line. (Notice 1: While locking the nuts, please lock two diagonal nuts firstly and lock tightly all the nuts then. Notice 2: Recommend to install the main body before setting up the fans. ). |
|
|
|
|
|
| Put one side of fan clip on the fan holder and another side buckles on the heatsink, and hoop up the other fan clips step by step. (According the demands, users can choose to install heatsink, or heatsink with one or two fans.). |
|
|
| Finally, plug in the power connector and finish the installation. |
|
